PTU Scrap kit is  Vickie by Rissa Designs

Artwork is by  Alex Prihodko, you can purchase at Picsfordesign.

New Transparent raster layer 650x650. You can resize this later if needed.

Open frame 2 copy and paste as new layer
resize down 1 time by 80% and place in the center

open paper 3 copy and paste as new layer
Move below the frame layer and erase all parts on the outside of the frame

Open your tube copy and paste as new layer
Resize down about 4 times by 80% and move to the left
Open your tube again, copy and paste as new layer
Place as desired below the frame layer and erase all excess
add a luminance legacy

open splatter 2 copy and paste as new layer
Move to the right below all other layers

Open the razor copy and paste as new layer
resize down about 3 times by 80%
free rotate to the left by 32% and move to the right
below the full length tube layer

open the bottle copy and paste as new layer
resize down about 3 times by 80%
move above the razor layer and slightly to the left.

open the spider copy and paste as new layer
resize down by 80% about 6 times
Move below the tube layer and on top of the bottle

open the candle copy and paste as new layer
resize down by 80% about 3 times
Move to the right below tube layer

Adjust where your other elements are

add name copyright and save

Written on 3 October 2012 * Using my own mind and creativity and similarities are completely coinicdental*

Tube is by Barbara Jensen,  You can purchase her tubes at her store.

PTU Scrap Kit is Remember by Stormy Rein Scraps, 

Purchase at The Scrappers Den
Mask of choice

New Transparent Raster Layer 800x800

Open frame 3 copy and paste as new layer
Resize down  by 80% about 2 times
Move down slightly still leaving in the center

open paper 7 copy and paste as new layer
Move below all other layers
Go to layers , Load mask from image
Merge group and move down slightly to line up with the frame

Open your close up tube layer copy and paste as new layer
Move below the frame layer
Erase all parts on the tube on the outside of the frame
Add a luminance legacy

Open the Bling copy and paste as new layer
Resize down by 80% about  4 times 
Move to the bottom above all other layers

Open full legnth tube copy and paste as new layer
Move below the bling placing to where her leg is covered by
the bottom wire
add a Xero Porcelain with the following settings

Open ribbon3 copy and paste as new layer
Resize down about 3 times by 80%
Move below the bling layer

open ribbon copy and paste as new layer
resize down  by 80% about 5 times
Move to the top and below the tube layer

open butterfly2 copy and paste as new layer
resize down by 80% about 4 times
Free rotate to the left by about 20%
Move to the top left  above the ribbon

Open the rose copy and paste as new layer
Resize down by 80% about 3 times
Move to the bottom right above all other layers

Add name copyright and save

Artwork is by Bonnies Creations, Do not use without a proper license to do so.

PTU Scrap Kit Pandora by Naughty Angel Creations

New transparent raster layer 800x800
We can resize later if desired

open frame 2 copy and paste as new layer
Resize down 1 time by 80% and move slightly down off center

open paper 7 copy and paste as new layer
Move below all other layers and erase parts on the ouside of the frame

open the tube copy and paste as new layer
Resize down about 2 times by 80% and place below the frame layer
Duplicate frame and move above the tube and erase parts covering the tube

open the music notes copy and paste as new layer
Move to the bottom above all layers

oepn image 27 copy and paste as new layer
Resize down by 80% about 4 times
Place mid center sitting on the music notes on the right

image 26 copy and paste as new layer
resize down by 80% about 2 times and move to the right below the bird

open image 23 copy and paste as new layer
resize down by 80% about 3 times and move to the right above element26

open element 9 copy and paste as new layer
Resize down by 80% about 2 times
Move element 23 above the tip of element 9

open element 17 copy and paste as new layer
Mirror and move to the left
below the tube layer

Add copyright, name and save